Traxxas Disruptor VXL-4s Brushless Race Boat W/ Rapid-Right Self-Righting COMBO W/4S & Charger

This is the Traxxas Disruptor VXL-4s Brushless Race Boat w/ Rapid-Right Self-Righting 4S Lipo COMBO Package with iD Charger, with Waterproof Electronics, TQ 2.4 GHz 2-Channel Radio System, Velineon VXL-4s Marine Speed Control with Brushless Outrunner Motor, and Factory-Applied Graphics.

4S LIPO COMBO PACKAGE INCLUDES
Traxxas Disruptor VXL-4s Brushless Race Boat w/ Rapid-Right Self-Righting
Traxxas 2981 EZ-Peak Plus 4s iD Charger
Traxxas 2890X 6700 mAh 14.8 V 4-cell 25C LiPo Battery

Full-Throttle, Non-Stop Fun
The 4s Disruptor is the one boat that holds nothing back. The fun begins when you pin the throttle and Disruptor launches hard on its way to 40+ mph on a single 4s LiPo battery. At 26″ long, Disruptor is perfectly sized to be quick and agile on small ponds and stable in open water. Disruptor is purpose-built by Traxxas for the wildest stunts and unstoppable fun—all with Rapid Right self-righting security.

RAPID RIGHT SECURITY
There’s no need to back off the throttle or tone down the fun with Disruptor’s Rapid Right security. Take full advantage of 4s Velineon brushless horsepower anytime, anywhere. If Disruptor should land upside down, applying reverse full throttle rights the boat almost instantly and gets you back in the action.

AGILE HANDLING
Disruptor’s perfectly sized hull delivers agile handling for tight turns with equally impressive 40+MPH speed. A new low-CG design concentrates weight inboard along the centerline for perfect weight distribution. Hammer the throttle and Disruptor gets on plane quickly with lightning-fast reflexes and high-speed stability.

4s POWER SYSTEM
The Velineon VXL-4s Marine brushless power system is a clean-slate design optimized to deliver maximum thrust on a single 4s LiPo battery. The all-new brushless outrunner motor is a model of efficiency and power, combining thunderous torque with high-RPM speed. Two independent water cooling systems keep temperatures in check for maximum run time.

Injection-Molded ABS Hull
Disruptor’s ABS hull provides the superior strength and rigidity required for high-voltage brushless horsepower without excess weight. The unique injection-molded design features multiple support trusses and ridges for exceptional strength. Molded bosses secure the removable electronics tray in place with minimal hardware for additional weight savings.

Features

• 26″ Deep-V Hull
  • Made from lightweight injection-molded ABS
  • Internal buttresses and bracing
  • Pre-applied graphics
  • Modular electronics tray
  • Foam bow insert
• Rigid Injection-Molded Clipless Hatch
  • Four quick-release hatch nuts with tool
  • Foam seal to repel water
  • Includes optional wingnuts
• 40+MPH with Single 4s LiPo Battery
• TQ 2.4 GHz Transmitter
  • Full-size 2-channel transmitter
  • All-day comfort with precise long-range control
  • 3-channel micro receiver with fail-safe security
  • Patented waterproof receiver box
• Rapid Right Self Righting
  • Rights an overturned boat almost instantly
  • Requires no special skills
• VXL-4s Marine Speed Control
  • Water-cooled aluminum heat sink
  • Innovative waterproof design
  • Programmable Drive Profiles
    • Sport Mode – forward / brake / reverse
    • Training Mode – 50% forward / brake / 50% reverse (patented)
  • Built-in two-stage low-voltage detection for LiPo batteries
  • LiPo battery packs: 2-4 cells (7.4 to 14.8 volts)
• Brushless outrunner Motor
  • 14-pole outrunner design
  • Ultra high-temperature sintered Neodymium magnets
  • Efficient, high-speed ball bearings
  • Optimized for power in marine applications
  • 5 mm output shaft
• Extra-Long 180 mm Battery Tray
  • Centralizes battery weight
  • Accommodates multiple battery sizes
  • Secure hook-and-loop straps
• Driveline
  • Direct drive 0.15-inch flex cable
  • Quick-release motor collet
  • Blue-anodized aluminum drive strut
  • Low-maintenance bushings
• Steering
  • High-torque waterproof 2056 servo
• Blue-anodized aluminum rudder
• Precision-Cut Stainless Steel Trim Tabs and Turn Fins
• Stainless Steel Hex Hardware Used Throughout

High Performance Prop
Disruptor’s prop gets the boat on plane quickly to reach maximum speed with the least current draw. Traxxas engineers tested countless prop configurations to find the perfect balance of performance, efficiency, and durability. Molded composite construction makes the prop light and tough, with no balancing or sharpening required.

High Strength Aluminum Hardware
Disruptor’s rudder and drive strut are machined from tough 6000-series aluminum for maximum strength and then anodized vivid blue for that unmistakable Traxxas look. The drive strut uses special oiled bushings for corrosion-free performance.

Stainless Steel Trim Tabs and Turn Fins
Dual trim tabs and turn fins are critical to Disruptor’s high-speed performance. The parts are precision die-cut and bent from stainless steel to resist corrosion as they provide aggressive cornering ‘bite’ and the proper hull attitude for extreme speed.

Dual Water Inlets and Outlets
Dual water pickups in the hull route cooling water to the motor and ESC independently. A streamlined dual-outlet plate on the transom evacuates water from the rear of the boat.

Clipless Latching System
Disruptor comes outfitted from the factory with heavy duty, low-profile hatch nuts to keep the rigid ABS hatch securely fastened. Just a quick turn with the included hatch nut tool gives you full access to the hull. Disruptor also includes a set of optional wingnuts for quick toolless installation and removal.

Flex Cable Drive System
Originally designed for outrageous 6s power, Disruptor’s flex cable drive system is efficient, reliable, and ready for all day fun. Disruptor’s electronics tray moves the motor further back towards the transom for a shorter and more direct path to the prop.

Waterproof Electronics
Waterproof electronics are a must in a marine environment. Traxxas electronics are fully waterproof (not just water resistant). The speed control, servo, and receiver all feature rugged waterproofing protection for dependable operation you can count on.

*Click to See the Full Line of Parts/Accessories

Specifications
Hull Type: Deep-V
Hull Length: 26.22 inches (666 mm)
Overall Length: 29.76 inches (756 mm)
Beam: 7.64 inches (194 mm)
Height: 5.91 inches (150 mm)
Deadrise: 25 degrees
Weight (no battery): 3.66 pounds (1.66 kg)
Speed Control: VXL-4s Marine electronic speed control
Motor (electric): 14-pole brushless outrunner
Cooling: Independent dual-inlet water cooling
Hull Material: Injection-molded ABS
Drive System: Direct drive 0.15-inch flex cable
Prop: 42 mm 2-blade composite (59 mm pitch)
Outdrive: Anodized aluminum
Steering Servo: 2056 waterproof
Radio System: TQ 2.4 GHz (2-channel)
Receiver: 6519 2.4 GHz 3-channel
Skill Level: 2
Battery Compartment (L/W/H): 180 mm long x 49 mm wide

Requires
(4) AA batteries for transmitter

Videos

Hide Videos


Show Videos